Language
Login |Register
Home
Product Center
DC Electronic Load
SDL1000X series


SDL1000X/SDL1000X-E series Programmable DC Electronic Load



Product Overview

SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5 inch TFT-LCD display, a user-friendly interface and superb performance specifications. The SDL1020X/SDL1020X-E models feature an input range of 150 V/30 A 200 W while the SDL1030X/SDL1030X-E have an input range of 150 V/30 A 300 W. The SDL1000X series leads with measurement resolution of 0.1 mV/0.1 mA and the base SDL1000X-E series resolution is 1 mV/1 mA and adjustable current rise times from 0.001 A/μs~2.5 A/μs. For remote communication and control, the SDL series includes RS232/USB/LAN interface types. The SDL1000X series delivers stability over a wide range of applications and can meet all kinds of testing requirements. including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.

 


Main Feature

  • ▶ SDL1020X/SDL1020X-E (Single channel ): DC 150 V/30 A, total power up to 200 W
  • ▶ SDL1030X/SDL1030X-E (Single channel ): DC 150 V/30 A, total power up to 300 W
  • ▶ 4 static modes / Dynamic mode: CC/CV/CR/CP
  • ▶ CC Dynamic mode: Continuous, pulsed, toggled
  •  CC Dynamic mode: 25 kHz, CP Dynamic mode: 12.5 kHz, CV Dynamic mode: 0.5 Hz
  • ▶ Measuring speed of voltage and current: up to 500 kHz
  • ▶ Adjustable current rise time range: 0.001 A/us~2.5 A/us
  • ▶ Min. readback resolution: 0.1 mV, 0.1 mA
  • ▶ Short-circuit, Battery test, CR-LED mode, and factory test functions
  • ▶ 4-wire SENSE compensation mode function
  • ▶ List function supports editing as many as 100 steps
  • ▶ Program function supports 50 groups of steps
  • ▶ OCP, OVP, OPP, OTP and LRV protection
  • ▶ External analog control
  • ▶ Voltage, Current monitoring via 0-10 V
  • ▶ 3.5 inch TFT-LCD display, capable of displaying multiple parameters and statessimultaneously
  • ▶ Built-in RS232/USB/LAN communication interface, USBGPIB module (optional)
  • ▶ Waveform trend chart and easy-touse file storage and call functions
  • ▶ Includes PC software: Supports SCPI, LabView driver


Design Features


Steady state operating mode

  

Dynamic test mode up to 25 kHz (CC)

The SDL features four operating modes to provide flexible test capabilities. In CC mode, the electronic load will sink a constant current, regardless of the voltage at its terminals. In CV mode, the electronic load will cause a constant voltage to appear at its terminals. In CR mode, the electronic load will behave as a fxed resistance value. As shown in the figure, the electronic load will linearly change the current according to the input voltage. In CP mode, the electronic load will cause a constant power to be dissipated in the load.

The transient test allows switching between two different load values. A common application is to test the dynamic characteristics of a DC source or DUT (Device-Under- Test). The transient test function enables the load to periodically switch between two set levels (Level A and Level B). The highest frequency can be set to 25 kHz in CC mode. The highest frequency can be set to 12.5 kHz in CP modes.






4-wire SENSE compensation mode function



In CC/CV/CR/CW mode, when a load is connected to a power supply, it will cause a large voltage drop on the connection lines between tested instrument and terminals of load. Using remote sense, you can measure the voltage at the DUTs input terminals, effectively removing the additional error due to the voltage drop in the connection wires.
 





Simplfy complex sequencing using the list operation function

You can generate complex load sequences quickly using the list operation function. Here, you can edit the setpoints, dwell time, and slew rate for each step in the test. *Slew rate can only be edited in CC mode.





Program function


Battery discharge function

In program (auto-test) mode, you can generate a sequence of tests using different modes, mode parameters and durations. This function is useful for automatically executing a set of tests on a device then display whether the tests passed or failed. Test results are easily viewed by pressing the up and down buttons. The load provides 8 nonvolatile registers to save auto-test file for recall later. Each file contains 1-50 steps to set up. Auto-test function is especially useful in the designing battery charging circuitry.

The SDL1000X can also provide insight into battery performance by analyzing the discharge characteristics of the DUT. The SDL features three stop conditions for the discharge test: Voltage, capacity or time. The discharge process is immediately terminated if the stop conditions are met. This provides more control over the test termination and an extra layer of safety during critical tests. Throughout the test process the battery voltage, discharge current, discharge time and discharged capability is displayed clearly on the LCD panel.






CR-LED Mode


OCPT/OPPT Mode

The SDL1000X includes a CR-LED mode specifcally for LED driver testing. Basing on the traditional CR mode, CR-LED mode adds a diode breakover voltage setting. When the input voltage is above this set value, the DC load start to work. Thus, it can emulate the actual characteristics of an LED.

Over-current protection (OCPT) mode prevents drawing too much current from the DUT. After the input voltage reaches the Von point, the DC load will start to draw a current from the source after a delay time. The current value will increase by a certain step size at regular intervals. Simultaneously, the DC load will compare the input voltage to the OCP voltage:If it is lower, then the present current value will be compared to see if it is in the current range you have set. Within the range, the OCP test will evaluate Pass or Fail. If it is outside of the set range, the DC load will to increase drawing current and compare the voltage again.





Overpower-protection (OPPT) mode: When the input voltage has reached the Von point, the load will draw power after a delay time. The power value will increase by a step size at regular intervals. Simultaneously, the DC load will judge whether the input voltage is lower than OPP voltage you have set, if it is, then the present current value will be compared to see if it is in the current range you have set. Within the range, the OPP test will Pass or Fail. If it is outside of the set power, the load will continue to increase the power draw within the cut-off current range and compare OPP voltage with the input.



Voltage Rise/Fall speed test


Voltage threshold function

The electronic load is also equipped to directly measure voltage rise and fall times. It can calculate the time from one voltage to another without the need for additional measurement instrumentation. With an SDL1000X, you can save money and improve effciency.

The SDL1000X can be set to turn on or off if the input voltage is at, above, or below a set value. By defning these thresholds, you control when the load is active. Which minimizes test time and increases safety.






Waveform trend chart function


Save/Recall setting parameters

The electronic load includes a waveform display function and supports the following operations for the waveform: Pause, recording, and capturing the waveform. You can quickly observe the trends of parameter changes as they occur throughout the test.

The load allows you to save different types of fles to the internal and external memories. You can recall and read them when necessary.






External analog control


Multiple policy protection modes

The load allows the user to control current or voltage through external analog terminals (EXT PRG). Input a 0-10 V analog to adjust 0-100% rated voltage and current. It is very useful for those applications that need to change the input value with external signals.

The SDL1000X series Programmable DC Electronic Load provides five protection types: OVP, OCP, OPP, OTP and LRV. When OVP/OCP/OPP/OTP/reverse voltage protection (LRV) occurs, the load will immediately turn off the input and stop sinking. Then, a prompt message is displayed.



Product information Product No
150 V/30 A 200 W Programmable DC Electronic Load SDL1020X/SDL1020X-E
150 V/30 A 300 W Programmable DC Electronic Load
SDL1030X/SDL1030X-E
Standard Accessories
USB Cable -1
Quick Start -1
Calibration Certifcate -1
Power cord -1



                    For detailed specifications, please refer to《SDL1000X/SDL1000X-E Series Datasheet》




SeriesMin. readback resolutionDisplayCurrent Slew RateMeasuring speedCC Dynamic mode frequencyModeInput powerInput currentInput voltage
SDL1020X
0.1 mV, 0.1 mA 3.5 inch TFT-LCD display 0.001 A/us~2.5 A/us up to 500 kHz 25 kHz CC/CV/CR/CP 200 W 30 A 150 V
SDL1020X-E
1 mV, 1 mA 3.5 inch TFT-LCD display 0.001 A/us~2.5 A/us up to 500 kHz 25 kHz CC/CV/CR/CP 200 W 30 A 150 V
SDL1030X
0.1 mV, 0.1 mA 3.5 inch TFT-LCD display 0.001 A/us~2.5 A/us up to 500 kHz 25 kHz CC/CV/CR/CP 300 W 30 A 150 V
SDL1030X-E
1 mV, 1 mA 3.5 inch TFT-LCD display 0.001 A/us~2.5 A/us up to 500 kHz 25 kHz CC/CV/CR/CP 300 W 30 A 150 V

Address: Antongda Industrial Zone, 3rd Liuxian Rd, Bao’an District, Shenzhen         Shenzhen ICP 09076277 © 2015 

                                     Google+  SIGLENT website -- International